Brass Nylon Insulated Terminals - Male/Female/Flag Sleeves JW-TM03
Brass Nylon Insulated Terminals - Male/Female/Flag Sleeves JW-TM03 Thumb
Video Thumbnail

Brass Nylon Insulated Terminals - Male/Female/Flag Sleeves JW-TM03

📅 2022-11-14 👁️ 2,822
  • Model No: JW-TM03

  • Specifications

    Material: Brass
    Sheath: Nylon
    Temperature Rating: 105°C
    Surface Treatment: Tin plating
    Terminal Types: Male, Female, Flag sleeves
    Installation: Crimp connection (no welding required)
  • Inquiry now

JW-TM03 is a brass terminal with a nylon insulating sleeve, tin plated and rated 105°C, supplied as male tabs, female receptacles and flag sleeves. Connection is by crimping only - no welding or soldering at the joint - and the sleeve covers the barrel and the insulation entry.

A soldered joint on a stranded harness wicks solder into the strands and creates a hard, brittle section right where the wire flexes. TM03 crimps instead: the barrel is deformed onto the strand bundle and the nylon sleeve takes the bend behind it. Brass holds the tab geometry under repeated mating better than annealed copper, and the flag body turns the exit 90 degrees so the wire can leave a shallow enclosure.

The three body styles separate TM03 from the rest of the series. TM01 is a closed-eye ring, TM02 a non-insulated open fork, TM04 a pin terminal; TM03 is the only one covering male, female and flag bodies in a single series, which lets one harness use a common crimp tool and sleeve system across all three joints.

Key Features

1. Brass body, tin plated, holding tab and receptacle dimensions through repeated mating cycles better than annealed copper.

2. Nylon sleeve rated 105°C, covering the barrel and the insulation entry so flex load bypasses the crimp.

3. Three body styles in one series - male tab, female receptacle and flag sleeve - on a common crimp and sleeve system.

4. Crimp connection only, no welding or soldering, keeping the strand bundle annealed at the joint and the cycle free of heat.

5. Flag body turns the wire exit 90 degrees, for terminals set against a wall or under a low cover where a straight tab will not fit.

6. Push-on mating on the male and female bodies allows a joint to be opened for service without cutting the wire.

Technical Specifications

ParameterSpecification
ModelJW-TM03
Product typeInsulated male / female / flag terminal
MaterialBrass
SheathNylon
Temperature rating105°C
Surface treatmentTin plating
Terminal typesMale, female, flag sleeve
InstallationCrimp connection, no welding required
Supply formCarrier strip

Applications

— Control panel wiring - male and female push-on joints on relays, contactors and terminal adapters in 105°C cabinets.

— Appliance harnesses - flag terminals on elements and switches where the wire must exit at right angles to the tab.

— Automotive low-voltage circuits - male and female pairs on lamps, motors and sensors that are unplugged for service.

— Battery and power distribution - male tab joints on fuse holders and distribution blocks inside shallow enclosures.

— Pump, fan and solenoid leads - flag sleeve terminations where the terminal sits against a housing wall with no straight clearance.

Insulated tube terminals in red, blue, green and orange on carrier stripsRed, blue and yellow insulated fork terminals on strips rated 19A to 48ARed, yellow, blue and black insulated round terminals on carrier stripsTranslucent blue and red fully insulated female terminals with oval mouthFDFN female terminal drawing with UL, CE and SGS marks and size tableThree red fully insulated female terminals with square mouth on a stripFDFN square mouth female terminal dimension table in red, blue and yellowFully insulated male terminals in blue and red with MDNF size tableFully insulated flag female terminals in red with FLDNY size tableBlue, red and yellow insulated fork terminals with CE mark and current ratingInsulated tube terminals in orange, blue, white and red, CE markedThree red fully insulated flag female terminals on a strip with dimension drawingNon-insulating blade terminals on strip with CE mark and dimension drawing
Brass Nylon Insulated Terminals

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each