Automatic Rubber Plastic Sleeve Tube Belt Wire Cutter WPM-100
Automatic Rubber Plastic Sleeve Tube Belt Wire Cutter WPM-100 Thumb Automatic Rubber Plastic Sleeve Tube Belt Wire Cutter WPM-100 Thumb
Video Thumbnail

Automatic Rubber Plastic Sleeve Tube Belt Wire Cutter WPM-100

📅 2026-05-14 👁️ 740
  • Model No: WPM-100

  • Specifications

    Model Number: WPM-100
    Control System: Microcomputer Numerical Control
    Cutting Materials: Rubber sleeves, plastic sleeves, heat shrink tubes, PVC tubes, cable wires, insulating paper, twin surface tape, bonding tape, cotton belts, zippers
    Operation: Automatic, precise length setting
    Waste Rate: Low
    Application: Industrial cable harness manufacturing, tube/belt/wire sizing
  • Inquiry now

The WPM-100 is a bench-top cutter under microcomputer numerical control for sleeves, tubes, tape and flat belting. Length is keyed in on the membrane panel and the machine feeds, measures and cuts in one automatic cycle. The material list covers rubber and plastic sleeves, heat-shrink tube, PVC tube, cable wire, insulating paper, double-sided tape, bonding tape, cotton belt and zippers, so one unit serves the cutting steps that otherwise need a shear, a tape dispenser and a sleeve cutter.

A sleeve cut with a hand guillotine comes out skived or oblique, and a millimetre of error on a short sleeve is visible once it is slipped over a terminal. On the WPM-100 a pair of grooved feed rollers with spring-loaded yokes pulls the material a programmed distance off the reel and the guarded blade closes on it, so every piece in the batch is cut to the same length with a square end. The same roller set grips flat tape and belting as well as round tube, which is where a single machine earns its bench space in a harness shop.

Within the range, the WPM-245 is dedicated to corrugated conduit in 4-25 mm, and the WPM-0.5-10MM2 and WPM-5-150MM2 are pneumatic cable tools that cut and strip by blade cassette. The WPM-100 does not strip: it measures and cuts a set length, and its material list is wider than cable, taking sleeving, tape, paper and belt on the same feed.

Key Features

1. Microcomputer numerical control with keypad length entry; the feed stops at the programmed length without a scale or a mechanical stop to reset.

2. Automatic feed, measure and cut sequence, so one operator runs several machines and only reloads the reel.

3. Ten material types on the same feed: rubber sleeve, plastic sleeve, heat-shrink tube, PVC tube, cable wire, insulating paper, double-sided tape, bonding tape, cotton belt and zipper.

4. Grooved feed rollers in spring-loaded yokes, visible at the infeed, grip round tube and flat tape with the same pair.

5. Waste rate is specified as low; the measured feed limits offcut to the trim at the start of a reel instead of a trial piece per setting.

6. Guarded blade under a clear cover, with an emergency stop beside the display and a take-off tray that carries cut pieces clear of the blade.

Technical Specifications

ParameterSpecification
ModelWPM-100
Machine typeAutomatic sleeve, tube and belt cutting machine
Control systemMicrocomputer numerical control
Cutting materialsRubber sleeves, plastic sleeves, heat-shrink tubes, PVC tubes, cable wires, insulating paper, double-sided tape, bonding tape, cotton belts, zippers
OperationAutomatic feed and cut with precise length setting
Waste rateLow
ApplicationIndustrial cable harness manufacturing; tube, belt and wire sizing

Applications

— Control panel building: heat-shrink tube cut to length for terminal and splice insulation on panel wire.

— Harness shops: PVC tube and braided sleeving cut to branch lengths before assembly onto the board.

— Coil and transformer work: insulating paper cut to slot and phase insulation sizes.

— Adhesive converting: double-sided and bonding tape cut into fixed pads for coil wrapping and label backing.

— Textile and strap cutting: cotton belt and zipper tape cut to length for cable ties, bags and garment trim.

Automatic tube and belt cutter with touch panel and cooling fan on white cabinetFive blue guide channels with timing belts feeding flat cable under steel rollerCollage of cut materials: ribbon cable, heat shrink tubing, silicone and rubber tube
Auto Rubber/Plastic Sleeve Cutter WPM-100

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each