Automatic Copper Brazing Machine with Robotic Arm - WPM-155
Automatic Copper Brazing Machine with Robotic Arm - WPM-155 Thumb Automatic Copper Brazing Machine with Robotic Arm - WPM-155 Thumb Automatic Copper Brazing Machine with Robotic Arm - WPM-155 Thumb
Video Thumbnail

Automatic Copper Brazing Machine with Robotic Arm - WPM-155

📅 2023-01-07 👁️ 388
  • Model No: WPM-155

  • Specifications

    Model Number: WPM-155
    Air Pressure: 0.5-1.0MPa
    Voltage: AC220V/50Hz
    Maximum Power (Main Engine): 3.4kW
    Power (Main Engine): 1.5kW
    Maximum Power (Brazing Machine): 20kW
    Cooling Hydraulic Pressure: 0.2MPa
    Influent Temperature:
    Speed: 8 seconds/piece
    Dimensions: 2100mm x 900mm x 2100mm
    Floor Space: 5020mm x 2100mm
  • Inquiry now

The WPM-155 is an automatic high-frequency brazing cell for copper workpieces. A robotic arm takes the part from the feed, presents it to the brazing head and releases it to the unload side on an 8 second cycle, with a 20 kW brazing power supply driving the joint. Two vibratory bowl feeders on the machine base supply the mating components, and the brazing head is mounted on a vertical slide above the work table.

Hand brazing of copper terminals depends on how long the operator holds the torch and how much wire is fed, which shows up as cold joints or burnt insulation at the end of a shift. The WPM-155 fixes the sequence: the part is clamped, the induction head descends to a set height, brazing wire is fed, and the joint is held until the braze flows before the part indexes out. Air pressure is regulated between 0.5 and 1.0 MPa, and the brazing transformer is water cooled at 0.2 MPa with inlet temperature below 40 degrees C.

Compared with the hand-held WPM-15-80AB induction units, the WPM-155 trades portability for repeatability: coil position, dwell and wire feed are set once and repeated at 8 seconds per piece. It is a floor-standing cell - the machine measures 2100 x 900 x 2100 mm and needs 5020 x 2100 mm of floor space for the feeders and operator access - so it suits a dedicated line rather than job-shop work.

Key Features

1. 8 seconds per piece cycle, set by the machine rather than by operator pace.

2. 20 kW brazing power supply, with a main engine rated 1.5 kW continuous and 3.4 kW maximum.

3. Robotic arm handles load, braze position and unload, so the operator only loads the fixture.

4. Two vibratory bowl feeders on the base plate present the mating components to the pick position.

5. Water-cooled brazing head: cooling hydraulic pressure 0.2 MPa, influent temperature below 40 degrees C.

6. Runs on AC220V/50Hz with 0.5-1.0 MPa shop air; machine 2100 x 900 x 2100 mm, total floor space 5020 x 2100 mm.

Technical Specifications

ParameterSpecification
Model NumberWPM-155
VoltageAC220V / 50Hz
Speed8 seconds/piece
Max. power (main engine)3.4 kW
Power (main engine)1.5 kW
Max. power (brazing machine)20 kW
Air pressure0.5-1.0 MPa
Cooling hydraulic pressure0.2 MPa
Influent temperaturebelow 40 degrees C
Dimensions2100 x 900 x 2100 mm
Floor space5020 x 2100 mm

Applications

— Cable harness: brazing copper wire to ring and fork terminals before insulation sleeving.

— Appliance wiring: brazing stranded copper leads to brass terminals on heating elements and switches.

— Switchgear and contactors: joining copper braid to contact pads at a fixed heat input.

— Automotive harness: brazing battery cable lugs and ground straps in volume.

— Copper tube assemblies: brazing small-diameter tube fittings where flame would anneal the whole part.

Brazed wire assemblies with black heat shrink sleeves on both ends
Automatic Brazing Machine WPM-155

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each