The WPM-MAX2-70mm2 is an automatic heavy-duty cable cutting and stripping machine for 0.1-70 mm2 conductor. Cutting length is 1-9,999 mm at a tolerance of (0.2 +/- 0.002 x L) mm, front and rear strip 150 mm each, on 1,000 W at 220 V/110 V, with output of 3,000-8,000 pcs/h from a 60 kg frame of 420 x 390 x 280 mm.
The 70 mm2 class is where a bench stripper stops being a wiring tool: the conductor is stiff enough to straighten itself out of the feed, and a blade set for 2.5 mm2 will crush it. The MAX2 uses a hard tungsten steel blade and a 1,000 W drive, and states tolerance as a fixed 0.2 mm plus 0.002 x L, so the allowance at short lengths is explicit rather than implied. Blade geometry is set for PVC, silicone and glass-fibre insulation.
The MAX2-70 covers 0.1-70 mm2 on a 60 kg bench frame. The WPM-10-300mm/400mm (360) is the class above: 10-300 or 10-400 mm2, 32-roller drive, 10-inch screen and a 1,000 mm side-I strip. Below 10 mm2 the MAX2 is the faster machine at 3,000-8,000 pcs/h; above 70 mm2 the 10-300/400 takes over. Neither is a sheathed multicore machine - that is the WPM-680 or the WPM-YHT3.
Key Features
1. Conductor range 0.1-70 mm2 on one machine: 0.1 mm2 control wire and 70 mm2 battery cable run on the same blade set, with cut length referenced to the conductor.
2. Cutting length 1-9,999 mm with front and rear strip of 150 mm each set as separate values, so a 150 mm jacket window at the lug and a 20 mm strip at the terminal come off one cycle.
3. Cutting tolerance stated as (0.2 +/- 0.002 x L) mm: the fixed 0.2 mm allowance covers blade set and the proportional term holds across the 9,999 mm range.
4. 1,000 W drive at 220 V/110 V: the power is sized for a 70 mm2 conductor, which a 300-400 W bench unit cannot pull through without stalling mid-cut.
5. Hard tungsten steel blade ground for PVC, silicone and glass-fibre insulation, with depth programmed rather than fixed by the frame, so 0.1 mm2 and 70 mm2 share one blade.
6. Output 3,000-8,000 pcs/h on a 420 x 390 x 280 mm frame: the rate holds at the top of the range on short leads, where the cut cycle rather than the feed sets the time.
Technical Specifications
| Parameter | Specification |
|---|
| Model | WPM-MAX2-70mm2 |
|---|
| Machine type | Automatic heavy-duty cable cutting and stripping machine |
|---|
| Cutting and stripping cross-section | 0.1-70 mm2 |
|---|
| Cutting length | 1-9,999 mm |
|---|
| Stripping length front | 150 mm |
|---|
| Stripping length rear | 150 mm |
|---|
| Cutting tolerance | (0.2 +/- 0.002 x L) mm |
|---|
| Voltage | 220V/110V |
|---|
| Power rate | 1,000 W |
|---|
| Output | 3,000-8,000 pcs/h |
|---|
| Blade material | Hard tungsten steel |
|---|
| Weight | 60 kg |
|---|
| Dimension | 420 x 390 x 280 mm |
|---|
Applications
— Battery and inverter cable: 16-70 mm2 flexible cable cut to 200-1,500 mm with a 30-50 mm strip at each lug end.
— Earth and bonding conductor: 6-50 mm2 cable cut and stripped for terminal and clamp assembly in distribution panels.
— Welding and machine tool cable: 25-70 mm2 cable cut to fixed runs with one end stripped for a lug.
— Appliance and HVAC power leads: 1.5-6 mm2 PVC and silicone cable cut in volume at 3,000-8,000 pcs/h.
— Glass-fibre and high-temperature cable: 1-25 mm2 cable where the insulation has to be cut cleanly rather than torn.