The WPM-2503 wraps a nylon cable tie around a coil and tightens it in one automatic cycle, replacing the manual roll-and-tie step at the end of a cable line. It covers bundles from 1 mm to 50 mm in diameter with 100 mm, 120 mm or 150 mm ties, and runs at 2300 pcs per hour. The unit is floor-standing, 720 x 660 x 780 mm at 130 kg, on castors so it can be moved between lines.
The cycle is short enough that handling dominates: at 0.7 s for feeding, reeling, tightening and cutting, the operator is loading coils faster than the head can tie them, and the bottleneck moves upstream. Ties are fed from a vibrating bowl that orients each one before it reaches the jaw, so the head is never hand-loaded and never runs with a reversed tie. Loop tightness is set on a manual adjuster, which lets the same machine run a slack loop for a multi-core cable and a firm loop for a single flexible cord without a program change.
It is a machine, not a consumable. The JW-PK06 supplies the flat binding wire used by winding-and-tying heads, whereas the WPM-2503 uses moulded nylon ties out of a bowl; the WPM-100 cuts sleeve, tube and belt to length but stops there, and this unit is the one that closes the loop around a finished coil.
Key Features
1. 2300 pcs per hour, on a 0.7 s cycle that covers feeding, reeling, tightening and cutting in one sequence with no second operator station.
2. Bundle range of 1-50 mm diameter, run with 100 mm, 120 mm or 150 mm nylon ties, which covers light sets and multi-core power cable on the same head.
3. Vibration plate automatic feeding orients and presents each tie, so the jaw is loaded by the machine and the cycle does not stop for reloading.
4. PLC control with a touch screen sets the count and the cycle; a three-colour tower light shows run, stop and fault at the end of the line.
5. Tightness is manually adjustable, allowing the loop to be tuned to the cable jacket without editing the program.
6. 400 W at AC 220 V with shop air at 0.6 MPa, on a 130 kg, 720 x 660 x 780 mm frame with castors, plus an optional waste recycling unit for the cut tie tails.
Technical Specifications
| Parameter | Specification |
|---|
| Model | WPM-2503 |
|---|
| Machine type | Automatic handheld nylon cable rolling and tying machine |
|---|
| Equipment size | 720 x 660 x 780 mm |
|---|
| Weight | 130 kg |
|---|
| Power | 400 W |
|---|
| Voltage | AC 220 V |
|---|
| Air pressure | 0.6 MPa (+/-0.5) |
|---|
| Bundling diameter | 1-50 mm |
|---|
| Tie scope | 100 mm / 120 mm / 150 mm |
|---|
| Speed | 2300 pcs per hour, 0.7 s per cycle |
|---|
| Control method | PLC + touch screen |
|---|
| Feeding method | Vibration plate automatic feeding |
|---|
| Tightness adjustment | Manually adjustable |
|---|
| Waste recycling | Optional |
|---|
Applications
— Automotive wiring harness: coiled branches and sub-assemblies tied at the end of the cut-and-crimp line before they are packed for the chassis side.
— Christmas and decorative light strings: coiled light sets tied with 100-150 mm ties at 2300 pcs/h, where hand tying would set the line rate.
— Photovoltaic cable: DC leads coiled and tied for packing, with the loop tension set low enough that the insulation is not marked.
— USB, HDMI and power cord finishing: coil and tie in one cycle in place of a manual roll, twist and cut, on cable from 1 mm upward.
— Building steel bar binding and general assembly-line bundling: rod and bar bundles inside the 50 mm limit tied at a fixed tension.