Automatic Coaxial Cable Cutting & Stripping Machine WPM-9600S
Automatic Coaxial Cable Cutting & Stripping Machine WPM-9600S Thumb
Video Thumbnail

Automatic Coaxial Cable Cutting & Stripping Machine WPM-9600S

📅 2026-03-06 👁️ 2,374
  • Model No: WPM -9600S

  • Specifications

    Model Number: WPM-9600S
    Wire Capability OD: 0.80-5.5mm
    Maximum Strip Left End: 40mm
    Maximum Strip Right End: Unlimited
    Maximum Strip Layers: 4 layers
    Power Supply: 220V/50Hz
    Power: 380W
    Cutting Length: 70mm-9999mm
    Material Range: Coaxial cable
    Data Storage: 60 parameters
    Drive Mode: Motor, ball screw drive
  • Inquiry now

The WPM-9600S is an automatic coaxial cable cutting and stripping machine. It handles 0.8–5.5 mm outer diameter, cuts to any length between 70 mm and 9999 mm, and opens up to four layers. The left end strips to 40 mm and the right end has no strip-length limit, with 60 parameter sets stored on the controller and a 380 W drive on 220V/50 Hz.

Cutting and stripping happen inside one cycle, so a reel of coaxial cable goes in and finished, stripped lengths come out without a second handling step. The carriage runs on a motor and ball screw rather than a belt, which is what holds the 70–9999 mm cut length repeatable over a long run. Because the right-hand head has no strip limit, a full jacket removal over any length is possible at that end in the same cycle as the cut.

Against the WPM-9800 it covers larger cable but fewer layers: 0.8–5.5 mm with four layers here, 0.64–4 mm with eight layers there. It also cuts from 70 mm where the 9800 starts at 10 mm. Use the 9600S when the cable is coaxial in the upper 5.5 mm range and the ends need a standard two- or four-layer prep; use the 9800 when the layer count and the short cut lengths are the binding limits.

Key Features

1. Cut length from 70 mm to 9999 mm is set on the controller and held by a motor and ball screw carriage.

2. Four stripping layers per end, enough for jacket, braid, foil and dielectric in one pass.

3. Left end strips to 40 mm and the right end has no limit, so a full jacket pull-off runs in the same cycle as the cut.

4. 60 parameter sets stored in memory, which covers a full cable and connector family without re-entering values.

5. Cutting and stripping in one cycle removes the separate measuring, cutting and stripping steps.

6. 380 W drive on 220V/50 Hz with a 0.8–5.5 mm working range, so the machine runs from a standard single-phase outlet.

Technical Specifications

ParameterSpecification
ModelWPM-9600S
Machine typeAutomatic coaxial cable cutting and stripping machine
Wire capability OD0.80–5.5 mm
Max. strip layers4 layers
Max. strip left end40 mm
Max. strip right endUnlimited
Cutting length70–9999 mm
Data storage60 parameter sets
Drive modeMotor, ball screw drive
Power supply220V, 50 Hz
Power380 W
Material rangeCoaxial cable

Applications

— Coaxial jumper production: cable pulled from the reel, cut to length and stripped at both ends in one cycle.

— Base-station feeder assemblies: 0.8–5.5 mm cable cut to fixed runs and stripped for connector fitting.

— Cable harness kitting: lengths from 70 mm upwards cut and stripped to feed a crimping station.

— Test-lead batches: four-layer ends produced to the same 40 mm left-end length across a run.

— Video and instrumentation coaxial: short cut lengths stripped without a separate measuring step.

front view of automatic coaxial cutting and stripping machine with touchscreenrotary knife head with V-shaped stripping blade between timing belt pulleysdetail views of stripping knife, pulley wire feed and air pressure regulatordiagram of four coaxial cable stripping stages from jacket to conductorstripped coaxial wire samples in black and blue jacketsseven stripped coaxial cable ends showing different braided shields
Coaxial Cable Cutting Stripping Machine WPM-9600S

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each