Automatic 30ML PUR Hot Melt Desktop Glue Dispensing Robot WPM-551
Automatic 30ML PUR Hot Melt Desktop Glue Dispensing Robot WPM-551 Thumb
Video Thumbnail

Automatic 30ML PUR Hot Melt Desktop Glue Dispensing Robot WPM-551

📅 2026-03-19 👁️ 263
  • Model No: WPM-551

  • Specifications

    Model: WPM-551
    Working Range: 500/500/100 mm
    Programming: Import teaching programming or graphics
    Motion Patterns: Point, line, arc, circle, curve, multiple lines, spiral, ellipse
    Control System: Single-chip + hand box control
    Dispensing Head: PUR dispensing head/PUH dispensing head
    Dispensing Cylinder: 30ml or 50ml
    Minimum Discharge: 0.01ml
    Glue Frequency: 5 Time/SEC
    Load Capacity: 10kg
    Axial Speed: 0-600mm/sec
    Repeatability: ±0.02mm
    Program Record: At least 100 programs, 5000 points each
    Display: LCD Teaching box
    Motor System: Stepper motor
    Guide: Taiwan upper silver linear guide
    Wire Rod: Taiwan TBI silver bar
  • Inquiry now

WPM-551 is a desktop Cartesian dispensing robot built around a 30 ml PUR hot-melt cylinder. Working range is 500 x 500 x 100 mm, axis speed reaches 600 mm/s, repeatability is ±0.02 mm, minimum discharge is 0.01 ml and the glue frequency is up to five shots per second. Table load is 10 kg, which covers a multi-cavity harness fixture.

The adhesive is held in a 30 ml or 50 ml cylinder and pushed out by a piston, so the melt is not left open to the air between shots and the shot size is set by cylinder displacement rather than by air pressure alone. Against hand-applied hot melt, the head repeats the same bead path on every harness, and the 600 mm/s axis speed keeps the cycle short enough for a takt-time line. Programs are imported from graphics files or taught with the LCD teaching box.

It is narrower in scope than the WPM universal platform: one hot-melt head, one cylinder, 100 programs. Compared with 379 JW-GL04 it has no rotary axis, but it handles PUR hot melt, which the cold-adhesive machines in the group cannot run.

Key Features

1. Working range 500 x 500 x 100 mm with a 10 kg table load, sized for fixtures carrying several connectors at once.

2. Repeatability ±0.02 mm and minimum discharge 0.01 ml, which holds bead width on small pads and short seams.

3. Axis speed 0–600 mm/s with a glue frequency of 5 shots per second, so dot chains are laid without stopping the carriage.

4. Memory holds at least 100 programs of 5,000 points each, keeping a family of harness variants on the machine without reloading.

5. Motion library covers point, line, arc, circle, curve, multiple lines, spiral and ellipse, imported from graphics or taught with the LCD teaching box.

6. Taiwanese linear guide and TBI ball screw drive the axes on stepper motors, with the dispensing head available in PUR or PUH configuration.

Technical Specifications

ParameterSpecification
ModelWPM-551
Machine typeDesktop Cartesian hot-melt dispensing robot
Working range500 x 500 x 100 mm
Repeatability±0.02 mm
Minimum discharge0.01 ml
Glue frequency5 times/sec
Axis speed0–600 mm/s
Load capacity10 kg
Dispensing cylinder30 ml or 50 ml
Dispensing headPUR dispensing head / PUH dispensing head
Control systemSingle-chip controller with hand box
Program recordAt least 100 programs, 5,000 points each
DisplayLCD teaching box
DriveStepper motor, Taiwanese linear guide, TBI ball screw

Applications

— Cable harness assembly: PUR beads bonding splices, sleeves and breakouts before overmoulding.

— Connector backshells: hot-melt shots filling the cavity behind the contact block as a strain relief.

— Automotive wire sets: fixing corrugated conduit ends and felt tape terminations.

— Sensor and small housing sealing: a continuous PUR bead run around the perimeter before the lid is closed.

— Electronics: strain relief on flex tails and wire-to-board joints where a cold adhesive would wick.

WPM-551 desktop glue dispensing robot, white gantry frame and yellow dispensing valve over work platformGold hot melt dispensing valve with syringe barrel and assorted dispensing nozzle tipsWPM-551 teach pendant with LCD showing point and vertex dispensing instruction listDispenser control panel with temperature controller, air pressure gauge and blue regulating valveStepper motor rated 1.8 degree per step beside a black timing beltMean Well power supply and AirTAC pneumatic solenoid valve spare partsHot melt adhesive types: glue sticks, particles, blocks and PUR cartridgeSix photos of dispensing nozzle applying hot melt to sensors, PCB and LCD frames
Hot Melt Desktop Glue Robot WPM-551

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each