Pneumatic Tubular Terminal Crimping Machine for 0.08-10mm² Wires T6-4
Pneumatic Tubular Terminal Crimping Machine for 0.08-10mm² Wires T6-4 Thumb Pneumatic Tubular Terminal Crimping Machine for 0.08-10mm² Wires T6-4 Thumb
Video Thumbnail

Pneumatic Tubular Terminal Crimping Machine for 0.08-10mm² Wires T6-4

📅 2026-05-16 👁️ 684
  • Model No: T6-4

  • Specifications

    Pneumatic Tubular Terminal Crimping Machine for 0.08-10mm² Wires T6-4
    Crimping Range: 0.08-10mm²
    Output Force: 1.3T
    Air Pressure: 0.3-0.8MPa
    Dimensions: 251mm*100mm*150mm
    Weight: 5.52kg
  • Inquiry now

The T6-4 is a pneumatic crimping machine for tubular end sleeves and ferrules on 0.08 to 10 mm2 wire. It closes a hexagonal die around the sleeve with 1.3 t of output force from 0.3 to 0.8 MPa of shop air, in a 251 x 100 x 150 mm C-frame unit of 5.52 kg.

A hand crimping tool puts in whatever force the operator's grip delivers, so the same ferrule can be under-crimped at the end of a shift and over-crimped by a stronger hand, and the hex profile is rarely closed completely. Here the force comes from an air cylinder at a set pressure, so every sleeve receives the same 1.3 t and the hex die closes fully around it. The C-frame throat is guarded, and the die set sits in a round holder at the throat, so the machine can be moved between benches by its top handle and put back into service on the same air line.

It is the terminal-side unit of this group: the other machines prepare the wire, this one terminates it. It is built for tubular sleeves with a hex profile, not for insulated ring or blade terminals, which need a different die and a different crimp geometry.

Key Features

1. Crimping range 0.08 to 10 mm2, covering 0.08 mm2 control wire through 10 mm2 feeder in one machine.

2. 1.3 t output force from 0.3 to 0.8 MPa air pressure, so the crimp height is set by the regulator rather than by operator strength.

3. Hexagonal die profile closes six points evenly around the sleeve, seating it on the conductor strands all round.

4. Pneumatic actuation leaves both hands on the wire and the ferrule during the stroke.

5. C-frame throat with a guard over the die, so fingers cannot reach the closing die.

6. 251 x 100 x 150 mm and 5.52 kg with a carry handle, small enough to sit at the end of a wiring bench and be moved to another line.

Technical Specifications

ParameterSpecification
ModelT6-4
Machine typePneumatic tubular terminal crimping machine
Crimping range0.08 to 10 mm2
Output force1.3 t
Air pressure0.3 to 0.8 MPa
Crimp profileHexagonal
Dimensions251 x 100 x 150 mm
Weight5.52 kg

Applications

— Control cabinet and panel wiring, crimping ferrules on 0.5 to 10 mm2 panel wire before it enters a terminal block.

— Machine builder wiring, terminating single and twin ferrules at the bench with a repeatable crimp height.

— Sensor and actuator leads, crimping 0.08 to 1.5 mm2 sleeves on small-device cable.

— Appliance and HVAC harness, terminating multi-core cable ends before connection.

— Switchgear feeder cables, crimping 6 to 10 mm2 tube terminals where a hand tool cannot close the hex fully.

Red T6-4 pneumatic terminal crimping machine with tubular ferrules and crimped wire samplesHands inserting insulated ferrules into T6-4 crimping die in two-step sequenceFerrule positioner gauge plate marked 6-10 checking a crimped wire terminalThree piece positioner plates for different wire sizes beside a crimped ferrule close-upYellow foot pedal switch for T6-4 crimper with 173 x 153 x 134 mm dimensionsT6-4 and T6-6 crimping machine specification sheet with crimp profiles and connection diagram
Pneumatic Tubular Terminal Crimper T6-4

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each