Automatic Coaxial Cable Cutting & Stripping Machine WPM-9800
Automatic Coaxial Cable Cutting & Stripping Machine WPM-9800 Thumb
Video Thumbnail

Automatic Coaxial Cable Cutting & Stripping Machine WPM-9800

📅 2026-03-05 👁️ 1,944
  • Model No: WPM-9800

  • Specifications

    Model: WPM-9800
    Wire Capability OD: 0.64-4mm
    Maximum Strip Left End: 40mm
    Maximum Strip Right End: Unlimited
    Maximum Strip Layers: 8 layers
    Power Supply: 220V/50Hz, 380W
    Cutting Off Length: 10mm-9999mm
    Cutting Depth Unit: 0.01mm
    Strip Accuracy: ±0.1mm
    Display Mode: 7 inch LCD in English
  • Inquiry now

The WPM-9800 is an automatic coaxial cable cutting and stripping machine for 0.64–4 mm outer diameter. It opens up to eight layers, cuts from 10 mm to 9999 mm, and holds strip accuracy to ±0.1 mm with a cutting depth unit of 0.01 mm. The controller uses a 7 inch LCD in English and the 380 W drive runs on 220V/50 Hz.

Eight layers inside a 4 mm envelope is the defining figure: a thin coaxial cable can be stepped through jacket, braid, foil, dielectric and inner insulation without moving the cable, which is where hand stripping normally loses the inner layers. The 10 mm minimum cut length suits short jumpers that a belt-driven machine cannot hold. Depth is set to 0.01 mm and the strip result is held to ±0.1 mm, so a batch of short leads keeps the same exposed conductor length.

Against the WPM-9600S it takes thinner cable and more layers: 0.64–4 mm and eight layers here, 0.8–5.5 mm and four layers there, and the minimum cut drops from 70 mm to 10 mm. Against the rotary-head WPM-6806D, which strips but does not cut to length, the 9800 adds the cutting carriage and the 9999 mm range.

Key Features

1. Eight stripping layers on cable down to 0.64 mm OD, covering jacket, braid, foil, dielectric and inner insulation in one cycle.

2. Cut length 10–9999 mm, so short jumpers and long runs are produced on the same machine.

3. Strip accuracy ±0.1 mm, with the cutting depth unit set at 0.01 mm.

4. Left end strips to 40 mm and the right end is unlimited, allowing full jacket removal at the outgoing end.

5. 7 inch LCD in English carries the layer and length parameters for the run.

6. 380 W drive on 220V/50 Hz; the machine cuts and strips in one cycle rather than two passes.

Technical Specifications

ParameterSpecification
ModelWPM-9800
Machine typeAutomatic coaxial cable cutting and stripping machine
Wire capability OD0.64–4 mm
Max. strip layers8 layers
Max. strip left end40 mm
Max. strip right endUnlimited
Cutting off length10–9999 mm
Cutting depth unit0.01 mm
Strip accuracy±0.1 mm
Display7 inch LCD, English
Power supply220V/50 Hz, 380 W

Applications

— Micro-coaxial jumper production: 0.64–4 mm cable cut from 10 mm and stripped through eight layers.

— Antenna and RF module leads: short cut lengths with a repeatable ±0.1 mm strip result.

— Medical imaging cable: thin coaxial cut to length and stepped for a miniature connector.

— Cable harness manufacturing: continuous cut-and-strip output feeding a terminating station.

— Instrumentation and sensor coaxial: braid and foil opened at separate depths on the same run.

cutting machine on stand with cable prefeeder, CE and ISO 9001 marksclose-up of stripped coaxial cable ends with copper braid
Coaxial Cable Cutting Stripping Machine WPM-9800

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each