Automatic Coaxial Cable Stripper Machine with 9 Blades WPM-28
Automatic Coaxial Cable Stripper Machine with 9 Blades WPM-28 Thumb Automatic Coaxial Cable Stripper Machine with 9 Blades WPM-28 Thumb
Video Thumbnail

Automatic Coaxial Cable Stripper Machine with 9 Blades WPM-28

📅 2026-05-15 👁️ 845
  • Model No: WPM-28

  • Specifications

    Model Number: WPM-28
    Peeling Length: 0.1-30mm
    Peeling Length Setting Unit: 0.01mm
    Cutting Scope: 0.3-6.99mm
    Cutting Depth Setting Unit: 0.01mm
    Processing Capacity: Approximately 200/hour
    Maximum Processing Steps: 9 Steps
    Data Storage Capacity: 9 types × 99 programs
    Wire Types: General wire, coaxial, semi-soft cover-line
    Noise Level: 60dB
  • Inquiry now

The WPM-28 is a bench-top coaxial cable stripping machine for cable from 0.3 to 6.99 mm outside diameter. Peel length is set from 0.1 to 30 mm in 0.01 mm increments, and the machine runs up to nine stripping steps in a single cycle at approximately 200 pieces per hour, with a noise level of 60 dB.

Each layer of a coaxial cable needs a different depth and a different length, and the WPM-28 stores both per step, so jacket, shield and dielectric are opened in one clamping sequence instead of three separate setups. Depth and length are entered in 0.01 mm units on the touchscreen rather than set with a caliper and a hand knife, which is where hand stripping loses concentricity on foam dielectric. Programs are held as 9 cable types by 99 programs, so a changeover is a program recall rather than a blade reset.

The WPM-X600 in the same range covers 10-50 mm cable and peels by rotary stroke at 20-40 pcs/min, so it does not reach the small coax sizes or the nine-step layer sequence. The WPM-28 stops at 6.99 mm and is the machine for multi-layer small cable; the X600 is the machine for single-jacket large cable.

Key Features

1. Up to 9 stripping steps in one cycle, each with its own depth and peel length for jacket, shield and dielectric.

2. Depth and length setting resolution of 0.01 mm, entered on the touchscreen instead of set by caliper.

3. Cutting scope 0.3-6.99 mm OD and peel length 0.1-30 mm cover small coax and semi-soft cable.

4. Program memory of 9 cable types × 99 programs, so changeover is a recall rather than a blade reset.

5. Approximately 200 pcs/hour with a 60 dB noise level, allowing the unit to sit on a harness bench.

6. Blade head runs behind a transparent guard with a front clamp jaw; the screen carries peeling length and half-peeling pages for staged stripping.

Technical Specifications

ParameterSpecification
ModelWPM-28
Machine typeAutomatic coaxial cable stripping machine
Cutting scope0.3-6.99 mm OD
Peeling length0.1-30 mm
Peeling length setting unit0.01 mm
Cutting depth setting unit0.01 mm
Maximum processing steps9 steps
Program storage9 types × 99 programs
Processing capacityApproximately 200 pcs/hour
Wire typesGeneral wire, coaxial, semi-soft cover-line
Noise level60 dB

Applications

— RF and coaxial cable assembly: jacket, shield and dielectric removal on 0.3-6.99 mm cable in one cycle

— Antenna, GPS and camera coax leads for automotive harnesses: staged stripping at both ends

— Test and measurement lead fabrication: consistent peel length across production batches

— Medical and instrumentation cable: multi-layer stripping without nicking the shield

— Semi-soft cover-line processing: controlled depth on cable that deflects under a straight blade

Coaxial Cable Stripping Machine WPM-28

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each