Automatic Flat Ribbon Cable Cutting Stripping Crimping Machine WPM-SP20
Automatic Flat Ribbon Cable Cutting Stripping Crimping Machine WPM-SP20 Thumb Automatic Flat Ribbon Cable Cutting Stripping Crimping Machine WPM-SP20 Thumb
Video Thumbnail

Automatic Flat Ribbon Cable Cutting Stripping Crimping Machine WPM-SP20

📅 2026-05-17 👁️ 1,411
  • Model No: WPM-SP20

  • Specifications

    Automatic Flat Ribbon Cable Cutting Stripping Crimping Machine WPM-SP20
    Control System: Japanese Panasonic
    Drive System: Panasonic Servo
    Operation Interface: Touch Screen Control
    Crimping Speed: Up to 22000pcs/hour
    Terminal Types: PH, XH, ZH, SCN, SM, VH, DuPont
    Operation Mode: Double-end crimping, single-end crimping, interval crimping
    Special Function: 2pin cable can output 5pcs simultaneously
    Stripping Capability: Half or fully stripped ends
  • Inquiry now

The WPM-SP20 cuts flat ribbon cable, strips the ends and crimps both ends in one cycle, in double-end, single-end or interval crimping mode. It runs on a Panasonic control system with Panasonic servo drives and a touch screen for pitch, length and crimp position, at up to 22,000 pcs per hour. Terminal families covered are PH, XH, ZH, SCN, SM, VH and DuPont, and a 2-pin cable can discharge 5 pcs at a time.

Flat cable is normally sheared, split and then crimped lead by lead, and the split is where pitch error starts. The SP20 positions the ribbon on the servo axis, separates the conductors and presses both ends without an operator handling the cable between steps. Interval crimping allows skipped positions on a ribbon, and half or full stripping is selected per job, so one set-up covers jumper families that would otherwise need separate fixtures.

The SP20 is the only flat-ribbon machine here and the fastest, at 22,000 pcs per hour against 3,200 wires per hour on the 501S and 530-650 times per hour on the WPM-5505. It does not tin, does not insert housings and does not run single-conductor wire; within this group those jobs belong to the 501S, the WPM-5505 and the JW-CM06 respectively.

Key Features

1. Flat ribbon cable cut, stripped and crimped at both ends in one cycle

2. Double-end, single-end and interval crimping modes

3. Crimping speed up to 22,000 pcs per hour

4. Panasonic control system and Panasonic servo drive, touch screen parameter entry

5. Terminal types PH, XH, ZH, SCN, SM, VH and DuPont

6. 2-pin cable outputs 5 pcs simultaneously; half or full stripping at either end

Technical Specifications

ParameterSpecification
ModelWPM-SP20
Cable TypeFlat ribbon cable
Control SystemJapanese Panasonic
Drive SystemPanasonic servo
Operation InterfaceTouch screen
Crimping SpeedUp to 22,000 pcs/hour
Terminal TypesPH, XH, ZH, SCN, SM, VH, DuPont
Operation ModesDouble-end crimping, single-end crimping, interval crimping
Special Function2-pin cable outputs 5 pcs simultaneously
StrippingHalf or fully stripped ends

Applications

— Consumer electronics jumpers: PH and DuPont terminals on flat cable, both ends crimped

— Appliance internal ribbon harnesses: XH and ZH terminals, interval crimping for skipped positions

— Display and instrument looms: SCN and SM terminals on fine-pitch ribbon

— Board-to-board links: 2-pin ribbon cable at 5 pcs per cycle

WPM-SP20 flat ribbon cable cutting stripping crimping machine with two JST terminal reelsFinished flat ribbon harnesses with pink striped insulation and crimped terminals at both ends
Auto Flat Cable Double End Crimp WPM-SP20

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each