The JW-ZW16C is a fully electric, fully automatic wire stripping and bending machine built for electrical wires up to 16 mm². It performs stripping and bending of both wire ends in one continuous process, turning loose reel wire into formed, ready-to-install jumpers without any manual cutting, stripping or bending.
All parameters — stripping length, bending angle, segment length and processing quantity — are set directly on a colour touch screen. Up to 200 programs can be stored in memory, so switching to a different wire size or jumper pattern is a single key recall instead of a full reset.
Unlike conventional machines that strip and bend one end only and are operated with a keypad, this model works through a brand touch screen interface and handles both ends. Bending angle and bending length are freely adjustable, which removes the quality differences of hand work and keeps every piece identical, while lifting output well above manual bench production.
An optional PC control system, inkjet printer and laser marking unit can be added when the line needs central programming or on-wire identification.
Key Features
- Fully electric drive — no pneumatic supply required; plug into a standard AC 220–250 V, 50/60 Hz outlet and start production.
- Colour touch screen with intuitive parameter setting; stripping length, bending angle and segment length are entered directly in the program.
- Memory for up to 200 programs — different wire types and jumper patterns can be called up with one key.
- Both ends stripped and bent in the same cycle, with clockwise and counter-clockwise bending available.
- Bending angle and bending length freely adjustable; up to 20 bending segments per wire (extendable).
- Processing capacity of 600–1000 pcs/hour, depending on wire type and program complexity.
- Cutting tolerance of ±0.002 × L for stable, repeatable jumper lengths.
- Optional PC control system, inkjet printer and laser marking unit for integration into automated lines.
Technical Specifications
| Parameter | Specification |
|---|
| Model | JW-ZW16C |
|---|
| Power Supply | AC 220–250 V, ≤50/60 Hz |
|---|
| Stripping Length | Wire head 1–100 mm; wire tail 1–25 mm (depending on wire) |
|---|
| Bending Length | 1–9999 mm; maximum 100 m |
|---|
| Minimum Bending Size | 15 mm (smaller sizes available on request) |
|---|
| Cutting Wire Range | Up to 16 mm² |
|---|
| Cutting Tolerance | ±0.002 × L |
|---|
| Conduit Diameter | 4–16 mm |
|---|
| Number of Bending Segments | 20 segments (extendable) |
|---|
| Output | 600–1000 pcs/hour (depending on wire) |
|---|
| Bending Method | Clockwise and counter-clockwise |
|---|
| External Dimensions | L 600 × W 450 × H 550 mm |
|---|
| Weight | 56 kg |
|---|
| Optional Items | PC control system; inkjet printer; laser marking unit |
|---|
Applications
- Control cabinets and electrical cabinets — pre-formed internal wiring and panel jumpers.
- Contactor forward/reverse wiring — repeated, identical jumper loops at consistent lengths and angles.
- Wire harness and terminal workshops — stripping and forming before crimping or screw connection.
- Equipment builders and maintenance departments — on-site production of replacement jumpers.
Why Choose the JW-ZW16C
Manual stripping and bending depends on the operator: lengths drift, angles vary and output stops when the operator stops. The JW-ZW16C replaces that with a repeatable program. Once the angle, length and segment count are stored, every piece produced from the same program matches the previous one, and any operator can run the machine after a short introduction.
Because the machine is fully electric, it needs no compressor or air line — an important advantage for small workshops and for installation on site. The 200-program memory covers a full range of panel and jumper patterns, and the optional PC control, inkjet printer and laser marking unit allow the machine to grow with the line.
Customisation and Options
The standard minimum bending size is 15 mm; smaller bending sizes can be produced to order. Bending segments can be extended beyond the standard 20. Please state your wire size, stripping lengths, bending angles and required output when requesting a quotation, so the machine can be configured for your application.