Semi-Automatic Cable Cutting Winding Machine with Meter Counter WPM-2009LC
Semi-Automatic Cable Cutting Winding Machine with Meter Counter WPM-2009LC Thumb Semi-Automatic Cable Cutting Winding Machine with Meter Counter WPM-2009LC Thumb
Video Thumbnail

Semi-Automatic Cable Cutting Winding Machine with Meter Counter WPM-2009LC

📅 2026-05-15 👁️ 483
  • Model No: WPM-2009LC

  • Specifications

    Model Number: WPM-2009LC
    Winding Speed: 1-10 circles/sec
    Tying Wire Length: 120-200mm
    Cable Tie: Rubber wrapped iron wire
    Suitable Coil Diameter for Tying: φ18-45mm
    Voltage: AC220V 60Hz
    Cable Coil Diameter: non-standard (customizable)
    Rated Power:
    Winding Interval: non-standard (customizable)
    Total Weight: 40kg
    Tying Speed: 0.6 times/sec
    Dimensions: L500*W300*H400mm
  • Inquiry now

The WPM-2009LC measures cable by meter counter, cuts it to length, winds it into a coil and ties the coil with rubber-wrapped iron wire. Winding runs at 1 to 10 cycles per second and tying at 0.6 ties per second, with a tie length of 120-200 mm closing coils of 18-45 mm. The winding dish and the winding interval are both listed as non-standard, which means the coil diameter is built to the customer's coil rather than taken from a fixed set of sizes. Cable enters through the feed and cut head on the left and leaves as a tied coil on the dish at the right.

Measured coils are normally made in three separate steps: pull and mark the length, wind it, then tie it. Each step adds its own error, and the length marked by hand is the one that reaches the customer. On the WPM-2009LC the meter counter is in the same pass as the cut and the wind, so the coil that is tied is the coil that was measured. The operator sets the length and the tie follows on the same cycle, which removes the handling between steps and the mismatched lengths that come with it.

Within the 2009 group this is the compact cut, wind, count and tie unit: 40 kg, 500 x 300 x 400 mm, under 200 W. The WPM-2009 winds only, with preset winding numbers and a 0.5-4 mm wire range, and the WPM-2009L adds adjustable winding with 50-300 mm winding rod spacing but no tying head. The WPM-5-30 is the larger automatic machine at up to 30 m of winding, 1-13 circles per second and 1500 W. Where a shop needs a bench unit that delivers a tied, measured coil, the 2009LC is the one in the group that does all four.

Key Features

1. Coil diameter is built to order (non-standard), with the winding interval also customizable, so the dish matches the coil the customer packs.

2. Ties at 18-45 mm coil diameter with rubber-wrapped iron wire cut to 120-200 mm.

3. Winding at 1-10 circles per second, tying at 0.6 ties per second.

4. Meter counter, cutting head and winding dish work in one pass, so the tied coil carries the measured length.

5. Cut and wind are driven from the same control cabinet, with start, stop and reset on the front panel and parameters on the touchscreen.

6. Under 200 W on AC 220 V, 40 kg on a 500 x 300 x 400 mm bench frame.

Technical Specifications

ParameterSpecification
ModelWPM-2009LC
Winding speed1-10 circles/sec
Tying speed0.6 times/sec
Tying wire length120-200 mm
Cable tieRubber wrapped iron wire
Coil diameter for tying18-45 mm
Cable coil diameterNon-standard, customizable
Winding intervalNon-standard, customizable
VoltageAC 220 V, 60 Hz
Rated powerbelow 200 W
Dimensions500 x 300 x 400 mm
Weight40 kg

Applications

— Power cord assembly: measure, coil and tie AC and DC cordsets to a fixed length at the end of the line.

— USB and HDMI cable packing: short data leads coiled to the customer's diameter and tied before bagging.

— Cable distributors: bulk cable cut into measured coils for resale, with the coil diameter built to the buyer's spec.

— Harness shops: sub-assembly leads measured and closed into transport coils.

— Appliance manufacturers: internal wiring leads cut and coiled to length at the sub-assembly station.

WPM-2009LC details: pneumatic cutting blade, disc clamp winding spindle and tie formerCoiled cable samples with tie diameter callouts and KSEON touch screen panel
Semi-Automatic Cable Cutting Winding Machine with Meter Counter WPM-2009LC

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each