Automatic Wire Stripping & Crimping Machine 5000pcs/h WPM-2008A2
Automatic Wire Stripping & Crimping Machine 5000pcs/h WPM-2008A2 Thumb Automatic Wire Stripping & Crimping Machine 5000pcs/h WPM-2008A2 Thumb
Video Thumbnail

Automatic Wire Stripping & Crimping Machine 5000pcs/h WPM-2008A2

📅 2026-05-17 👁️ 2,167
  • Model No: WPM-2008A2

  • Specifications

    Wire Stripping & Crimping Machine 5000pcs/h WPM-2008A2
    Measurement: W410×L460×H420mm
    Weight: 85kg
    Power Supply: AC220V
    Compressed Air: 0.6MPa
    Pressure: 2000kg
    Stripping Length: 1.0-7.0mm
    Capacity: AWG#18-36
    Feed Way: Side feed
    Production Capacity: 5000-6000pcs/h
  • Inquiry now

The WPM-2008A2 is an automatic wire stripping and crimping machine for AWG#18 to AWG#36 wire. It strips 1.0–7.0 mm at the end and crimps the terminal in the same cycle, producing 5000–6000 pcs/h with 2000 kg of crimping pressure from 0.6 MPa compressed air. The unit measures 410 × 460 × 420 mm, weighs 85 kg and runs on AC220V.

The terminal strip is fed from the side, with the reel carried above the press and the strip guided down past the stripping station, so the crimp point and the strip point sit in one plane and the wire never leaves the clamp between the two operations. Pressure is applied by a pneumatic press at 2000 kg rather than by a lever, which holds the crimp height constant across a run. Side feed also leaves the front of the applicator open for the operator to change terminals.

It is the higher-throughput of the two crimping models and the lighter press. The WPM-2008A2-E uses end feed, strips to 10 mm instead of 7 mm, and raises pressure to 3000 kg at 3000–3500 pcs/h. The 2008A2 is the choice for short strip lengths on small terminals where 5000–6000 pcs/h matters more than strip reach.

Key Features

1. Stripping and crimping in one cycle at 5000–6000 pcs/h, with no second handling of the wire between the two operations.

2. 2000 kg pneumatic crimping pressure from a 0.6 MPa air supply, applied by press rather than by a hand lever.

3. Strip length 1.0–7.0 mm, set for the terminal series in use.

4. AWG#18–36 capacity covers small-gauge signal and control wire on one applicator.

5. Side feed carries the terminal strip in from the side, keeping the front of the applicator clear for terminal changes.

6. 410 × 460 × 420 mm, 85 kg, AC220V: a bench-top unit that needs no floor space or foundation.

Technical Specifications

ParameterSpecification
ModelWPM-2008A2
Machine typeAutomatic wire stripping and crimping machine
Wire capacityAWG#18–36
Stripping length1.0–7.0 mm
Production capacity5000–6000 pcs/h
Crimping pressure2000 kg
Compressed air0.6 MPa
Feed waySide feed
Power supplyAC220V
Dimensions (W×L×H)410 × 460 × 420 mm
Weight85 kg

Applications

— Appliance wiring harness: AWG#18–24 leads stripped at 1.0–7.0 mm and crimped with a ring or spade terminal.

— Control panel harness: AWG#22–28 signal wire terminated in one pass at 5000–6000 pcs/h.

— Sensor and connector leads: short strip lengths on fine AWG#28–36 wire.

— Automotive sub-harness: small-gauge branch wires stripped and crimped before loom assembly.

— Electronic module pigtails: terminal crimped at a fixed height on every piece without a height adjustment between reels.

stripped three-core cable with ferrules crimped on the endsrow of crimping machines installed along a factory workbenchhundreds of terminal crimping applicators lined up on an assembly benchfront view of stripping and crimping machine with TE terminal reellabeled diagram pointing out take-up reel, terminal mould and clamping cylinderrear view diagram labeling air regulator, motor and foot pedal socketcrimped open-barrel terminals on colored wires held in handsix panels of wire harnesses with crimped terminal endsLED counter operation panel and red tact switch close-uphorizontal feed terminal mould close-up beside flexible LED work light
Wire Stripping Crimping Machine WPM-2008A2

Send us your question about this product

No file chosen
JPG / PNG / WebP, up to 10 MB each